BS EN 61284:1998

Although created for fittings above 45 kV the standard may also be applied to lower voltages and to similar fittings for substations.

Cross References:
IEC 60437:1973
ISO 209-1:1989
ISO 426-1:1983
ISO 426-2:1983
ISO 427:1983
ISO 428:1983
ISO 630:1995
ISO 683-1:1987
ISO 683-13:1986
ISO 1083:1987
ISO 1187:1983
ISO 1336:1980
ISO 1459:1973
ISO 1460:1992
ISO 1463:1982
ISO 2604-1:1975
ISO 3506:1979
ISO 3522:1984
ISO 3574:1986
ISO 3755:1991
ISO 5922:1981
ISO 6361-2:1990
ISO 6362-2:1990
ISO 6363-2:1993
ISO 6932:1986 IEC 60050-466:1990
IEC 60060-1:1989
CENELEC HD 588.1 S1
IEC 60120:1984
CENELEC HD 474 S1
IEC 60372:1984
IEC 60471:1977
IEC 60826:1991
IEC 61089:1991
CISPR 16-1:1993
CISPR 18-2:1986
ISO 1461
ISO 9000-1:1994
EN ISO 9000-1:1994
ISO 9001:1994
EN ISO 9001:1994
ISO 9002:1994
EN ISO 9002:1994
ISO 9003:1994
EN ISO 9003:1994
ISO 9004-1:1994
EN ISO 9004-1:1994
ISO 2859-1:1989
ISO 2859-2:1985
ISO 3951:1989




Keywords: Overhead power-line fittings; Overhead power lines; Electric power transmission lines; Design; Corrosion protection; Marking; Electrical safety; Type testing; Classification systems; Dimensions ; Hot-dip galvanizing; Mechanical testing; Tensile testing; Heat transfer; Interference (wave physics); Acceptance specification; Radio disturbances; Voltage measurement; Approval testing; Formulae (mathematics); Magnetic measurement; Test equipment; Circuits; Clamps (mechanical); Electrical connections; Electric load cycling tests ; Testing conditions

Product Code(s): 30078357,30078357

This product references:BS EN ISO 9000-1:1994 - Quality management and quality assurance standards. Guidelines for selection and use
BS EN ISO 9001:1994 - Quality systems. Model for quality assurance in design, development, production, installation and servicing
BS EN ISO 9002:1994 - Quality systems. Model for quality assurance in production, installation and servicing
BS EN ISO 9003:1994 - Quality systems. Model for quality assurance in final inspection and test
ISO 1461:1999 - Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods
ISO 9001:1994 - Quality systems - Model for quality assurance in design, development, production, installation and servicing
ISO 630:1995 - Structural steels - Plates, wide flats, bars, sections and profiles
ISO 3522:1984 - Cast aluminium alloys - Chemical composition and mechanical properties
ISO 3755:1991 - Cast carbon steels for general engineering purposes
ISO 6362-2:1990 - Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles - Part 2: Mechanical properties
ISO 6363-2:1993 - Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes - Part 2: Mechanical properties
ISO 2859-2:1985 - Sampling procedures for inspection by attributes - Part 2 : Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
ISO 3951:1989 - Sampling procedures and charts for inspection by variables for percent nonconforming
ISO 209-1:1989 - Wrought aluminium and aluminium alloys - Chemical composition and forms of products - Part 1: Chemical composition
ISO 6361-2:1990 - Wrought aluminium and aluminium alloy sheets, strips and plates - Part 2: Mechanical properties
ISO 683-1:1987 - Heat-treatable steels, alloy steels and free-cutting steels - Part 1 : Direct-hardening unalloyed and low-alloyed wrought steel in form of different black products
ISO 1460:1992 - Metallic coatings - Hot dip galvanized coatings on ferrous materials - Gravimetric determination of the mass per unit area
ISO 1187:1983 - Special wrought copper alloys - Chemical composition and forms of wrought products